KymiraKymira is a composite material with the characteristics and properties of traditional sheet form Solid Surface but at considerably less cost and with none of the design constraints.
It can be produced in various sized sheets from 5mm to 30mm thick or Kymira can be spray applied onto a range of substrates with almost any edge thickness at all. It can also be sprayed into molds to allow for an incredible range of design applications.
Whether traditional or avant-garde Kymira is a perfect choice for home, office or commercial applications.
Kymira Solid Surface has the elegant look of natural stone, yet it is non-porous ( can not harbour bacteria ) and possesses far greater fabricating flexibility. This enables endless design possibilities for beautiful living and working environments.
Kymira is:
| • Affordable |
• Bacteria & Fungi resistant |
• Durable |
• Stain & Corrosion resistant |
| • Attractive |
• Thermal shock resistant |
• Renewable |
• Solvent resistant |
| • Flexible |
• Impact resistant |
• Seamless |
• Acid resistant |
| • UV Stabilised |
• Colour consistent |
• Lightweight |
• Easy to create inlays |
| • Warm to touch |
• Fire retardant |
Kymira solid surface is available in an almost infinite colour range and matte, satin, gloss and textured finishes. We advise that you use the matte finish for work surfaces. Dark colours will require more maintenance and care than light colours.
Kymira is avaliable from all good kitchen and joinery manufacturers throughout New Zealand. You can ask them to supply you with a quote and we will be happy to provide colour samples.
The uses of Kymira are limited only by your imagination, however here are some suggestions:
kitchen tops, vanity tops, table tops, retail counters, commercial counters, laundries, spa bath surrounds, reception counters, wall panels, sanitary areas, bar tops, lighting pelmets, shop fittings, hospitals, boat fitouts, laboratories, medical facilities, hotels & motels.
Care and Maintenance
Kymira is an extremely durable and versatile material, with normal use and certain precautions, it will maintain its appearance for many years.
To keep Kymira looking it’s best, we advise the following maintenance procedures … … failure to adhere to these may void the warranty.
1. Kymira tops may look a little dull or patchy when they are first installed, this is normal and they will develop a more consistent look after 2 to 3 weeks. Kymira should be cleaned using general cleaners such as spray and wipe or warm soapy water. To remove small scratches and marks, occasionally go over the surface with liquid Jif and a damp cloth, using a circular motion. Dark colours will require more care than light ones.
2. Do not cut directly onto your Kymira surface. Whilst cuts can be removed from the surface it is
recommended that you always use a chopping board.
3. Kymira may be damaged by placing hot pans from the oven or stove top directly on to it …… always use heat shield or insulated pad under crock pots, electric frypans or other hot pots.
4. Avoid allowing harsh chemicals such as nail polish remover, oven cleaner or drain cleaners to come into
contact with Kymira. If any of these chemicals are spilt they must be flushed from the surface with warm
soapy water immediately.
5. Difficult marks to remove may be rubbed with a cream cleaner such as liquid Jif, or diluted Janola.
5. To remove deep scratches or cuts from Kymira, wet sand using a block, or dry sand using a random
orbital sander with 320 grit sandpaper. Sand in a circular motion over a wider area to prevent hollowing
until scratches are removed. Use a grey scotchbrite pad with
a cream cleaner (Jif ) over the entire top. If your top is a gloss finish it will require machine buffing.
6. Matte finish tops can be periodically resurfaced by going over the entire surface with a cream cleaner and a
scotchbrite pad. Kymira tops can be bought back to their original appearance after years of use. Contact your supplier for more information.
Ifyou require any information about Kymira, please contact Wright Marble Ltd.
Warranty
It is important that you read the care and maintenance of Kymira sheet before filling out this warranty form, as misuse may void this warranty.
Wright Marble Ltd will, in the event of a claim being made and at it’s sole discretion, replace, repair or refund up to the original price paid, for a period of six years after the original purchase date .
This warranty is dependant on the following of procedures as laid out in the care and maintenance of Kymira sheet.
Physical abuse such as heat cracking and associated damage, burns, cuts heavy weight and chemical damage are not covered by this warranty.
Although premium quality pigments have been used in Kymira, Wright Marble Ltd have no control over the environmental conditions that Kymira may be subjected to and therefore the guarantee does not extend to colour changes.
I acknowledge, as owner/ purchaser of Kymira, installed at the address listed below, that I have read and understood both the conditions / limitations of the warranty herein and the care and maintenance of Kymira procedures as laid out.
To read more about Solid Surfaces, click here.
For fabrication specifications click here.
|
